Hard touch sleek slider caps.

Note: These caps do not fit on LED sliders

DATASHEET

Hard touch sleek slider caps available in three colours – Black, Grey and White.

Note: These caps do not fit on LED sliders

DATASHEET

These PT range knobs are made in the USA by Rogan, they are not official Mutable Instruments or Make Noise products, but are the same range from the same factory. You should not consider them Make Noise ‘spares’ for example, there may be subtle differences.

• PT-1PS: small white pointer knob (all knobs on Branches, Shades, Shelves, Streams, etc)
• PT-1S: small black/white encoder knob, no pointer (small)
• PT-2S: medium black encoder knob, no pointer (medium, i.e. Braids encoder knob)
• PT-2PS (D-shaft): medium white pointer knob (i.e. Braids knobs, Frames top row, etc)
• PT-3PS: large white pointer knob (i.e. big knobs on Clouds, Elements, Tides, etc)
• PT-5PS: Larger white pointer knob (i.e. same size as large knobs on QPAS, DPO etc)
• PT-6PS: Extra large white pointer knob (i.e. same size as largest knobs on Frames, Warps etc)

Refer to the Rogan data sheet Rogan to check dimensions and other information.

Please NOTE: You remove existing knobs from your modules at your own risk, don’t force them! Also please check what shaft types you need first BEFORE ordering. Module manufacturers do not always consistently use a certain shaft type, they may change between D or T18 for example. Note that T18 knobs do not fit on 6.35mm round shaft pots.

NEW! 5PS knobs!

As seen on DPO and QPAS.

X-Large 6PS

As seen on Warps and Frames.

We now sell hex keys for the small, medium & large knob sizes, the small knobs use a very small imperial sized key for which there isn’t a good metric alternative (0.05 inch). Please take care using this key and don’t use excessive force to over-tighten the screws, due to the very small diameter it is quite easy to blunt the key. The medium key is 1/16th inch.

These RB range knobs are made in the USA by Rogan and have been frequently used by Verbos Electronics as well as on Buchla systems. They feel great to touch, and look fantastic on all types of panels. These 6.35mm knobs are made with ABS plastic with a matte finish, and will fit perfectly on our Alpha 9mm Pots.

Note: these knobs use bushings and set screw(s) – they require a small hex-key rather than a screwdriver to tighten them.

Dimensions

inches/mm

inches/mm

BULK DISCOUNTS

| 25+  – 5% | 50+  – 7% | 100+  – 10% | 250+ – 20% |

(Bulk prices are calculated once items are added to your cart)

NOTE! These do not work on shorter trimmer pots. The 6mm diameter plastic shaft must extend at the very minimum 8mm from the panel surface for these to work, please measure before ordering. The ideal length of plastic shaft is 12mm. These knobs are not designed for T18 pots.

A brand new knob designed by Thonk

We’ve been searching for some time to find the ideal knob to make tall trimmers better to wiggle with. We wanted a knob that would feel more tactile to handle, whilst still retaining the convenient grip and slimness of trimmer pots. We also wanted colour options which would pair nicely with our other ranges of knobs. T18 knobs are too prone to damaging Tall Trimmers so we went through a careful prototyping process to get the fit of these just right. Behold the Tall Trimmer Topper!

These knobs are strictly designed for Tall Trimmer Potentiometers which you can buy HERE. They are not designed for use on T18 pots, they kind of work on T18 pots but we don’t recommend them for that so buy for that purpose at your own risk.

NOTE! These do not work on shorter trimmer pots such as those on the Korg Volca range. The 6mm diameter plastic shaft must extend at the very minimum 9.5mm from the panel surface for these to work. The ideal length of plastic shaft is 12mm. These knobs are not designed for T18 pots.

External Dimensions: Height: 13.95mm | Width: 7.8mm

NOTE! These do not work on shorter trimmer pots such as those on the Korg Volca range. The 6mm diameter plastic shaft must extend at the very minimum 9.5mm from the panel surface for these to work. The ideal length of plastic shaft is 12mm. These knobs are not designed for T18 pots.

A = Audio (Logarithmic) – B = Linear

BULK DISCOUNTS

Discounts are calculated on any combinations of type and value.
Add pots to the cart to see the actual cost for buying in bulk. Email for larger volumes.

Shaft Diameter – 6.35mm (0.25″)

Shaft Length – 15mm (0.59″)

These are the pots that are included with 95% of all Thonk produced kits and specced by many manufacturers. These pots work great with all the 6.35mm round shaft knobs we sell.

We love these pots, they feel smooth and precise and have got a strong following for a good reason. One thing that always annoyed us was that annoying little anti-rotation tag that you have to cut or break off, so unlike other distributors we got them manufactured without that tag. Also removing the nut and washer on each pot to build something like a 64 pot sequencer panel can get REALLY tedious, so again unlike other distributors we include the nut and washer bagged separately. It only save 20 seconds per pot maybe, but it adds up!

FULL DATASHEETS – http://www.thonk.co.uk/documents/alpha/9mm/

These pots are available in various values and styles including – A10K, A50K, A100K, A500K, A1M, B10K, B25K, B50K, B100K, B500K, B1M, C25K.

A = Audio (Logarithmic) – B = Linear

BULK DISCOUNTS

Discounts are calculated on any combinations of type and value.
Add pots to the cart to see the actual cost for buying in bulk. Email for larger volumes.

Shaft Diameter – 6.35mm (0.25″)

Shaft Length – 20mm (0.79″)

These pots are almost identical to our regular Alpha round shaft pots but they have a longer shaft of 20mm (10mm thread). The longer shaft is useful when using thicker DIY front panels or when using larger knobs with a high placed set screw.  These pots work great with the 6.35mm round shaft knobs we sell, but do check the project specifications carefully to see if the longer shaft is suitable.

Apart from the shaft and thread length all other specs are the same as our shorter 15mm Alpha round shaft pots.

These pots have the same smooth and precise action as the rest of our Alpha range. There’s no anti-rotation tag that you have to cut or break off, and the nut and washer bagged separately. It only saves 20 seconds per pot maybe, but it adds up!

FULL DATASHEETS – https://www.thonk.co.uk/documents/alpha/9mm-long

These pots are available in various values including – A50K, A100K, A1M, B10K, B50K, B100K, B1M.

A = Audio (Logarithmic) – B = Linear

BULK DISCOUNTS

Discounts are calculated on any combinations of type and value.
Add pots to the cart to see the actual cost for buying in bulk. Email for larger volumes.

Shaft Diameter – 6mm (0.2″)

Shaft Length – 15mm (0.59″)

These are the same quality pots that are included with 95% of all Thonk produced kits and specced by many manufacturers. These pots work great with all the 6mm T18 Shaft knobs we sell.

These pots are perfect for Music Thing Modular, RYO, Random*Source, Fonitronik, Frequency Central (FCUK) & Erica Synths projects where 9mm pots are specced… but do double check as there are a few exceptions.

We love these pots, they feel smooth and precise and have got a strong following for a good reason. One thing that always annoyed us was that annoying little anti-rotation tag that you have to cut or break off, so unlike other distributors we got them manufactured without that tag. Also removing the nut and washer on each pot to build something like a 64 pot sequencer panel can get REALLY tedious, so again unlike other distributors we include the nut and washer bagged separately. It only save 20 seconds per pot maybe, but it adds up!

FULL DATASHEETS –  SINGLE GANG – Alpha T18 shaft

DUAL GANG DATASHEET FOR FOOTPRINT – Dual Gang

These pots are available in various values and styles including – A10K, A25K, A50K, A100K, A500K, A1M, B5K, B10K, B25K, B50K, B100K, B250K, B500K, B1M, Dual Gang, Centre Detent.

A = Audio (Logarithmic) – B = Linear

BULK DISCOUNTS

Discounts are calculated on any combinations of type and value.
Add pots to the cart to see the actual cost for buying in bulk. Email for larger volumes.

These pots are available in various values and styles including – A10K, A25K, A50K, A100K, A500K, A1M, B5K, B10K, B25K, B50K, B100K, B250K, B500K, B1M, C50K, Dual Gang, Centre Detent.

Shaft Diameter – 6.35mm (0.25″)

Shaft Length – 15mm (0.59″)

These are the pots that are included with 95% of all Thonk produced kits and specced by many manufacturers. These pots work great with all the 6.35mm round shaft knobs we sell.

These pots are perfect for Music Thing Modular, RYO, Random*Source, Fonitronik, Frequency Central (FCUK) & Erica Synths projects where 9mm pots are specced… but do double check as there are a few exceptions.

We love these pots, they feel smooth and precise and have got a strong following for a good reason. One thing that always annoyed us was that annoying little anti-rotation tag that you have to cut or break off, so unlike other distributors we got them manufactured without that tag. Also removing the nut and washer on each pot to build something like a 64 pot sequencer panel can get REALLY tedious, so again unlike other distributors we include the nut and washer bagged separately. It only save 20 seconds per pot maybe, but it adds up!

FULL DATASHEETS – http://www.thonk.co.uk/documents/alpha/9mm/

Alpha Dual Gang

A = Audio (Logarithmic) – B = Linear

BULK DISCOUNTS

Discounts are calculated on any combinations of type and value.
Add pots to the cart to see the actual cost for buying in bulk. Email for larger volumes.

These pots are available in various values and styles including – A10K, A25K, A50K, A100K, A500K, A1M, B5K, B10K, B25K, B50K, B100K, B250K, B500K, B1M, Dual Gang, Centre Detent.

Shaft Diameter – 6mm (0.236″)

Shaft Length – 15mm (0.59″)

These are the same quality pots that are included with 95% of all Thonk produced kits and specced by many manufacturers. These pots work great with all the 6mm D-Shaft knobs we sell.

These pots are perfect for Music Thing Modular, RYO, Fonitronik & Erica Synths projects where 9mm pots are specced… but do double check as there are a few exceptions.

We love these pots, they feel smooth and precise and have got a strong following for a good reason. One thing that always annoyed us was that annoying little anti-rotation tag that you have to cut or break off, so unlike other distributors we got them manufactured without that tag. Also removing the nut and washer on each pot to build something like a 64 pot sequencer panel can get REALLY tedious, so again unlike other distributors we include the nut and washer bagged separately. It only save 20 seconds per pot maybe, but it adds up!

FULL DATASHEETS – Alpha D-shaft | Alpha D-shaft Dual Gang

Knob Knobs are one of a kind, boutique handmade davies 1900h clones. You can use them on your modules, synths, effect pedals, guitar, amps, mixers!

Knob Knobs are very textural creatures, blue and green knobs features organic texture pigmentation, spark knobs feature glitter and enchantment.

These knobs are 6.35mm round shaft, If you want to these knobs with 6mm shaft knobs then you’ll need to use brass adaptors as shown below.

Soft Touch 6mm D-shaft knobs. These are the exact style of knobs as used on all Joranalogue modules

BASE DIAMETER: 12.5MM
HEIGHT: 17.1MM
SHAFT TYPE: 6MM D-Shaft

We now sell hex keys for the small, medium & large knob sizes, the small knobs use a very small imperial sized key for which there isn’t a good metric alternative (0.05 inch). Please take care using this key and don’t use excessive force to over-tighten the screws, due to the very small diameter it is quite easy to blunt the key. The medium key is 1/16th inch.

These RB range knobs are made in the USA by Rogan and have been frequently used by Verbos Electronics as well as on Buchla systems. They feel great to touch, and look fantastic on all types of panels. These 6.35mm knobs are made with ABS plastic with a matte finish, and will fit perfectly on our Alpha 9mm Pots.

Note: these knobs use bushings and set screw(s) – they require a small hex-key rather than a screwdriver to tighten them.

Dimensions

inches/mm

inches/mm